Ritz Safety
All Categories > Fall Protection > Roofing Anchors
Refine Results  
Results displayed: 1-10 of 22
Sort Results By:

Page Size:
Results page: 1 2 3
Item ID: MUT15903
  • Meets OSHA requirements for perimeter marking of any above ground construction area, flat roof jobs, and open upper-level construction
  • Exceeds the 500 lb. OSHA-required break strength
RL
Item ID: RTZ4000

Hinged Style Reusable Roof Anchor is for use on sloped or flat wood or steel roofs and easily installs with (20) nails or screws (depending on roofing application; screws and nails sold separately). Unit may be installed at pitched angles or flat with both plates resting on roof surface in opposite directions.

When attaching to wood truss over sheathing, center row of holes of both sides of this anchor must be secured by 2", #12 wood screws or equal.

Wood roof installation: 3/4" sheathing minimum, the outer row of holes on each side (10 holes per side, 20 holes total) must each be filled with a 16d x #20 nail or equal.

Steel roof installation: Only the inner row of holes on each side (6 holes per side, 12 holes total) must be filled with #12, 3/4" metal screws or equal.

Meets ANSI Z359.1 and OSHA 1910.66 & 1926.502 standards

EA
Item ID: RTZSA02

Hinged Style Reusable Roof Anchor is for use on sloped wood roofs and easily installs with (20) nails or screws. Meets all applicable OSHA regulations and ANSI standards.

EA
Item ID: RTZSA03

Simple install be nailing/screwing all holes into truss. The anchor features stainless steel construction with a one side stamped silver/golden yellow galvanized D-ring. Maximum breaking strength: 5,000 lbs. Meets ANSI Z359.1-2007 standards.

EA
Item ID: RTZ8000

Ritz Safety®'s Flat Mounted Disposable Roof Anchor is easy to install by nailing or screwing all holes into truss. Meets all applicable OSHA regulations and ANSI standards.

EA
Item ID: RTZN480

Ritz Safety®'s Sloped Mount Disposable Roof Anchor is easy to install by nailing or screwing all holes into truss on a top or slope knockdown roof. Meets all applicable OSHA regulations and ANSI standards.

EA
Item ID: RTZN5072F

Hinged Style Reusable Roof Anchor is for use on flat wood roofs and easily installs with (20) nails or screws. Meets all applicable OSHA regulations and ANSI standards.

EA
Item ID: GRD00250
Guardian's Standing Seam Roof Clamp is a temporary anchor point that is designed for use with SRLs (sold separately) up to 50ft in length, attaches to metal roof seams spaced from 24in - 36in apart, while allowing the attached SRL to rotate a full 360°, has a powder-coated steel construction for durability and is certified for maximum loads up to 3,600lbs.
EA
Item ID: MILRA41

Honeywell Miller®'s Single D™ Permanent Roof Anchor has a single D-ring and Meets all applicable OSHA regulations and ANSI standards

EA
Item ID: ACR21000
  • Acro's X-Warning Line Systems Kit includes four 36" x 36" x 42" high posts and 130' of warning flags that are quick and easy to setup or take down, creating a safety perimeter on commercial roofs or ground applications

  • Posts can be secured by screwing into place or with 20 lbs. of ballast (each sold separately)

  • Complies with all applicable OSHA regulations

EA
Results page: 1 2 3
Can't find what you're looking for?
  • Refine your search results
  • Let us help: Customer Service or call (800) 451-3077